It is highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . We offer our prestigious clients the premium range of Cement Remover RX Hold. Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver as an alternative to using hazardous acids for concrete removal. Back-Set is a one-of-a-kind formula. It uses an active ingredient found in sugar cane syrup, and is completely biodegradable.
RXSOL-22-2202-025 turned this vulnerability into an opportunity. "Back-Set" safely removes hardened concrete from a variety of difficult to clean surfaces. It break down the ionic bond in portland cement, releasing the cement from any surface to which it has adhered.
This liquid mixture specifically designed to deal with hard cases of cement cargo deposits or dry cement stains. Its proven advantage is the provision of immediate penetration and complete dissolution of cement, the result being a thorough cleaning.
Chemically Back-Set converts the positive ions in the hardened matrix into negative ions, which dissolves the cement into mud that can be rinsed away. Because it works chemically, rather than mechanically, Back-Set may be used to remove cured concrete, mortar, grout, and stucco from virtually any surface without harm.
ACTIVE MATTER : 98-100 %
WHY RXSOL-22-2202 is better ?
Biodegradable & non flammable , Economical very cost effective
Safe for paint, chrome, aluminum, glass, rubber, plastic, brass & stainless
Dissolves cured cement, concrete, mortar, grout, stucco
Also comes with a foaming spray nozzle
Will not remove rubberized cement
Suitable for the removal of cement deposits and dry stains.
Due to its higher concentration its chemical reaction is very fast.
It's chemical combination meet the requirements of paragraph 1.8.2 of the P&A Standards.The offered cement remover is broadly demanded for its effective usage & perfect composition. Moreover, our cement remover can be availed by us within the given time at reasonable rates to our customers.Features:
The hardened concrete is saturated with Back-Set, either with a brush or by spraying. After 15-20 minutes, the area is again saturated with the chemical. The concrete typically begins to soften in 20-30 minutes, and can be rinsed off with water.
The hardened concrete is saturated with Back-Set, either with a brush or by spraying. After 15-20 minutes, the area is again saturated with the chemical. The concrete typically begins to soften in 20-30 minutes,and can be rinsed off with water.The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of cement to be removed.5 to 20 % recommended .These are recommended values based on experience. For optimum results dose RXSOL-22-2202-025 directly to the surface .
The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of CEMENT to be removed . 5 to 20 % recommended .These are recommended values based on experience.
For optimum results dose RXSOL-22-2202-025 directly to the surface
Undiluted : In cases where we deal with heavy deposit build–up, CEMENT REMOVER must be applied undiluted.
Diluted : In cases of light deposition, on large surface areas, a solution between 10–40% may be used.
B. Cleaning Procedure
Undiluted/Diluted: In parts such as corner cavities, tank skeleton inlets, etc, Apply RXSOL-22-2202-025 through hard brush, mop, sponge or any other manual method. Let it soak for 15 minutes. Afterwards, wash thoroughly by applying high–pressure water source. In case of deposit persistence, repeat the cleaning procedure.
Refer to technical datasheet.
Ideally suited for slop tanks. Also recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. Low toxicity, non - corrosive. Highly effective, economical solvent cleaner.Dose:
For light contamination dilute with water in the ratio 1:20 . For medium contamination dilute with a petrosolvent. And for heavy contamination concentrated RXSOL-20-2006-020 is suggested.
For Engine Room & Cargo Tank Cleaner
Product Description:- RXSOL-20-2006-025 is an all purpose degreaser emulsifiers, It is an excellent blend of powerful solvent base and emulsifying inorganic products .Specially designed for engine room and cargo tank cleaning .Main feature of RXSOL-20-2006-025 is, it finally dissociate slop emulsion to separate oil and water .This provide us with ability to dispose of waste solution as per MARPOL & IMO rules and regulation .
Dosage:- Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended where as medium contamination dilution with Petro solvent , And for heavy contamination neat RXSOL CB 2006 is suggested to use.
Procedure of use :- RXSOL-20-2006-025 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2006-025 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning after Mineral Oils/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2006-025 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2006-025 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
COAL REMOVER :::
• Use cold - no heating required.
• Economical to use.
• Scraping not required.
• Non- flammable.
Directions for Use and Dose Rates
Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.
Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.
Application: For absorbing disagreeable odors in the refrigerator or other places that require deodorizing. Made from quality activator carbon. Furnished in small and large sizes
Other Valuable Product
1)Degreaser Soy and VOC Free Tar -
RXSOL-10-1724 is a new trend setting formulation that keeps pace with today’s safety and environmental regulations. Powerful natural ingredients are blended to out perform the conventional hazardous solvent degreasers. This natural degreaser concentrate instantly emulsifies grease, oils and fats without the use of harsh acids, alkali, or petroleum solvents. RXSOL-10-1724's organic extract is extremely strong, and works extremely well under the worst conditions. RXSOL-10-1724 has a wide variety of uses indoors and out. This product will remove most resins, adhesives, printing inks, decals, tar, rubber tire marks and asphalt. RXSOL-10-1724 also is an effective drain cleaner and maintainer. This product is v.o.c. free. part no:RXSOL-10-1724-025
2)Degreaser Heavy Duty - 25 ltr-
It is a unique formulation blended from inorganic, organic compounds and detergents with powerful dispersing agents. Readily soluble in water in all proportions. It is non-corrosive to metal like copper, aluminium, mild steel and plastic. It is non-toxic which makes handling easy.part no:RXSOL-10-1005-025
3)RED NBD PLUS RIG Degreaser-
Very effective products to removes grease, wax, vegetable and animal fat, oil, sludge, soot, carbon deposits, traffic film, dirt and grime. This DUAL POWER SURFACTANT BASED powerful cleaner works where others fail. Formulated with several different ingredients including a dual surfactant system. This formula works on extremely tough jobs that require extra strength. Concentrated, this product may be diluted with up to 200 parts water for greatest economy. This product may be used for degreasing and contains corrosion protection. Part no:RXSOL-10-1033-020
4)Degreaser SB 25 Ltr-
unique formulation blended from inorganic, organic compounds and detrgents with powerful dispersing agents. Readily soluble in water in all proportions. It is non - corrosive to metal like copper, aluminium, mild steel, and plastic.part no:RXSOL-10-1006-025
5)Degreaser Bio Degradable - 25 Ltrs-
Its Complex formulation makes It extremely effective for a broad spectrum of industrial and institutional applications, such as bakeries, bottling plants, breweries,boats, printing plants, public buildings, park dept,dockyards, food plants, vessels bilge's, deck engine rooms, and machine shops etc.part no:RXSOL-10-1102-025
6)Chembreak QUICK SEPARATING DEGREASER 25 Lt-
it has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker "C" cleaners. part no:RXSOL-20-2006-025
7)Degreaser Neutral Based 25 Ltr-
neutral pH cleaner suitable for general cleaning e.g after discharging gasoil.part no:RXSOL-10-1033-025
8)Odour Control Degreaser -
Description - Penetrating Pleasant Aroma Effectively Masks Any Odors That Are Present
· Reduces Grease Buildup
· High Solvent Action Reduces Clogging - Helps Keep Sewage Systems Clean and Free-Flowing
· Dilutes with 4 to 100 Parts Water Depending on Severity of Odor or Grease
· Improves Working Conditions - Eliminates public Complaints
Areas of Use: Sewage Disposal plants ·Waste Areas ·Refuse Cans and Trucks ·Manure Piles ·Solvent For the Removal of Grease, Oil, Detergents, Tar & Sludge ·Sludge Beds ·Drains and Grease Traps ·Warehouses Under Dock Plates ·Automotive Hoists.
Features & Benef ITS :
1> Non toxic , 100% biodegradable, Environmentally friendly
2> Heavy duty Hydrocarbon remover
3> Non caustic Safe to use in occupied / covered areas
4> Safe on skin , Can be easily applied by ship's crew
5> Can be diluted to suit cleaning needs
6> Reduces turnaround times
7> using an RXSOL Application Set
Depending on contamination 50 - 200 ml per 10 litrs of water . i. e. 200 mol to a bucket of water .
Method of Application and Dose Rates:
1.Direct injection method for washing machines. Dose rate 1-5 litres per ton wash water (0.1-0.5%).
2.Recirculation method. Dose rate 1-7 litres per ton wash water (0.1-0.7%).
3.Spot cleaning. Hand spray neat or diluted with up to Five parts water and leave for several minutes before rinsing off with clean water.Cleaning of Cargo Tanks to remove Soot from Inert Gas Systems.
5.Spray RXSOL-22-2204-210 on with a high pressure cleaning machine and use1:6 with water.If used with hand sprayer,spray the product neat onto the surface,allowing1 lit.for every12 m2.Use a5-8%solution in a tank washing machine.
6.Leave for about 30-45 minutes.The surface should be kept wet.
7.Wash down with hot water (80°C) and check the cargo tank
8.Repeat the procedure if necessary.
Note: Whenever possible,the cleaning solution should be heated to 60-80°C.If this method is not possible,other conventional methods such as separate rate direct injection,recirulation or hand spraying provide acceptable options.For boiler fire side cleaning,a 10-20 % hot solution, (temp.above 40°C),should be sprayed on to the surfaces to be cleaned.Allow to penetrate for 20 minutes and flush off. For deposits which are very hard to remove, increase the concentration to 50% and repeat if necessary
The use of RXSOL-22-2204-210 in correct dosages is half the job done.
FOR HOLD CLEANING :::
For Light cleaning 10 - 50% solution with water
For Moderate deposits 50 - 75% solution with water
For Heavy deposits 75% solution with water
3 Pieces of Good Advice
Apply RXSOL-22-2204-210 on dry surface where possible. A dry surface will absorb far better than a wet surface. Allow the product to soak for 10 - 30 minutes. Due to the wetting agents, emulsifier will stick to the wall longer, thereby increasing the contact time, resulting in a better cleaning effect.
When applying RXSOL-22-2204-210 on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the RXSOL-22-2204-210 may produce "channels" down the surface, thereby running too fast off the surface.
Make sure the solution on the wall doesn’t dry on the surface. Rinse the tanks by means of high pressure waterjetting. This removes the cleaning solution
including the residues.
During high pressure cleaning:It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw cleaner from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of RXSOL-22-2204-210 will give the best effect.
Quickly dissolves and removes grease and dirt deposits after emulsfication. Economical - dilute for most cleaning needs.Dose:
Dilute 0.3 to 5% of solution with fresh water.Note:
Bio-degradable and eliminates the need to buy and stock duplicate products because of its effectiveness in all areas.
It can be used as a general purpose cleaner to remove oil and grease deposits.First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2015-210 is by direct injection followed by recirculation washing, using tank cleaning machines. Spraying Method - Using LAC as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
** Make sure to take all safety precautions are followed when handling / spraying RXSOL-20-2015-210
Injection Method – not applicable.
Refer to technical datasheet
Re-circulation Method :
Fill tank with fresh water and heat up to warm 50 oC .IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and LAC to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
* Use a strainer at the pump stack when circulating any solution.*
Tank Lining – Stainless / Epoxy / Phenolic
MARINE - Rust Stain cleaner Metalic brightner ( foaming nature )RXSOL-20-1011-MBHD ( Metalic Brightener-Rx ) can be used as a spot cleaner after cleaning fats and fatty acids , can be used on painted surface .A superior heavy duty and highly Concentrated liquid blend of surfactant & organic compound containing rust penetrating agent, solubilizer and inhibited phosphoric acid with ionic and non ionic emulsifier. Dose:
FOR TANK CLEANING
RECOMMENDATION : 0.2% TO 100%
specially designed for removal of rust from any steel surface area and rust stain from Brass , Copper , S.S wood , ceramic and aluminium surfaces , painted or not . And act as surface brightner.
Procedure for Use :-
For steel surfaces; remove oil, grease and old paint. Wet down entire surface with neat Metal Bright- Rx and allow to dry. Second wash may be necessary. Surface should have a grey/white appearance when the Metal Bright- Rx is dry. Steel surfaces will have a resistance to rust and will render a good base for paint.For removal of rust stains on painted surfaces and wood, Metal Bright Rx should be applied at full concentration for heavy stains, or diluted to 20-50% for light stains. Allow to soak for 15 to 30 minutes and wash off with water. A second application may be necessary to remove the stubborn stains.
Spraying Direction :-
Using an empty / clean 210 liter drum, fill with 190 liter of fresh water and add 20 liters of Metal Bright Rx This makes a 10% solution, which can be sprayed onto areas in coated tanks where rust stains are showing and over actual rusted areas. Once spraying is completed, wait 20-30 minutes and fresh water rinse with lots of water, if possible use butterworth machines for a more efficient result. This method can be used in stainless tanks to “freshen up” the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the Metal Bright Rx will show up in a Wall Wash.
Injection – Not suitable.
When hand spraying is inadequate (too much area to cover), prepare a 2% - 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pumpstack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
Transparant, colourless crystals. Hazard: Toxic by inhalation and ingestion, strong irritant.
Uses: general metal and equipment cleaning, purifying agent and intermediate for many compounds. Oxalic acid's main applications include cleaning or bleaching, especially for the removal of rust (iron complexing agent), e.g. Bar Keepers Friend is an example of a household cleaner containing oxalic acid.
About 25% of produced oxalic acid is used as a mordant in dyeing processes.
It is used in bleaches, especially for pulpwood.
It is also used in baking powder.
Using Application :
Oxalic Acid is used extensively for boat cleaning, it can be used on timber, GRP and steel craft for the removal of rust and waterline stains and also to clean timber decks. For vertical applications oxalic can be mixed with wallpaper paste to make a thick solution, this mix will cling to any vertical surface and can be washed off with water.
OXALIC ACID CAN ALSO BE USED FOR:
Wood bleach, Rust removal, General stain cleaner, Brick stains,
Furniture restoration, Boat cleaning (GRP), Bee keeping.
REMOVAL OF IRON STAINS
Iron stains can be removed by scrubbing the stained area with an aqueous solution of oxalic acid in water. Dissolve 1kg oxalic acid to 6Lt of warm water. Scrub stained area using a stiff-bristle brush. Thoroughly rinse with water after treatment. When completely dry, lightly sand the surface. Surface must be clean and
completely dry (not just surface dry) before refinishing. Incomplete drying and retained subsurface moisture can cause finish adhesion failure.
Many of Construction Chemicals customers are involved with building renovation and in particular Oak frames, oak windows and beams as well as flooring. Our product range ensures that whenever timber is being used we have the products to bond, fill, preserve, sand, stain and paint. Our Customers will be aware of the problems of oak stains especially with green oak. This can look unsightly and spoil good looking beams or floors. OXALIC ACID CLEANS MOST STAINS FROM TIMBER.
Removal Of Black Water And Tannin Stain
A common form of staining on wood surfaces results from contamination with iron. A portion of the extractives in wood includes a group of chemicals collectively called tannins. The amount of tannins depends on species; oak, redwood, and cedar are rich in tannins. Tannins react with iron to form a blue-black stain on wood. Common causes of iron stain include use of un-galvanized or poorly galvanized fasteners; OXALIC ACID brushed into the stains makes removal easy. Finishing wood with a WATER REPELLANT WITHA PRESERVATIVE AND/ORWOOD POLISH OR OIL greatly minimizes further iron stain and enhances the finish of the wood.. Wood must be clean; free of paint, waxes, oils and dirt. Use wood cleaners to remove any grease oils or grime. Use paint strippers to remove any finish, paint or coating.
Application: For degreasing and removal of residues of minerals oil , coal stain and soot from surface.
S-2 Keep out of the reach of children.
S-26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S-36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S-45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).
Dose:Refer to technical datasheet. and the Material Safety Data Sheet before use. Always refer to any warning, instructions and labels supplied with the products.
Note:Not suitable for use with soft metal like aluminium, magnesium and zinc silicate coatings.
All chemical products should be handled with care. Protective clothing and respiratory equipment should be used where necessary.
Very effective emulsifier - based cleaner for use in hold cleaning and general digressing. its heavy molecular surfactants rapidly reacts with water and produce effective cleaning solution .May be applied by brush, hand spray and by high and low pressure washing machines.
It is a heavy duty non corrosive concentrated cleaning compound soluble in fresh and salt water , also suitable with high presure cleanig machines. Ideal for difficult cleaning problems faced in industrial and other plants, Very effective degreaser which removes dirt, oil and grease from the equipment, parts, components, engines, floors and walls etc.
RXTUFF HIGH FOAM LIQUID - HD (RXSOL-22-3002-HF)
The Importance of Rx Tuff by High-Pressure Cleaning
The job of high pressure cleaning can be done easier & quicker by simply using RxTuffin correct dosages. Using a high pressure cleaner alone, without any CLEANER, will not achieve optimal cleaning results High-pressure cleaning primarily refers to cleaning of Hard surfaces, such as Decks, Tanks, Engine-rooms, etc. and in the majority of cases the cleaning is done according to the so-called two-step method:
Step 1: Spraying the RxTuff over the area to be cleaned.
Step 2: Washing down the area using a high-pressure water jet.
After the RxTuff has been sprayed on the surface and before the wash down begins, the chemicals penetrates & thoroughly moistens dirt & other grime. During wash down, the RxTuff thoroughly dissolv- es the particles of dirt, even oil and fat, in the water spray and thus achieves optimal cleaning results.In addition to being more effective, the use of RxTuff substantially reduces the time required for the Cle -aning operation, as well as preventing dirt from reforming on the surface. The use of RxTuff in correct dosages is half the job done.
3 Pieces of Good Advice:
Apply RxTuffon dry surface where possible! A dry surface will absorb far better than a wet surface. When applying RxTuff on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the RxTuff may produce "channels" down the surface, thereby running too fast off the surface. During high pressure cleaning: It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw soap from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of RxTuff will give the best effect .
Product Description:-RxTuff is a superior & powerful alkaline cleaner containing corrosion inhibitors to prevents the corrosion of metals . It is low toxic product with an exceptional solvency power on soil & oily matter & having good foaming qualities. It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials .
Applications:-RxTuff Suitable for cleaning engine components like fuel and Lube oil filters, Injection nozzles, pump components, inlet and exhaust valves & primarily refers to cleaning of hard surfaces, such as Decks, Tanks, Engine-rooms, etc. can be used for all types of cleaning and degreasing and may be applied by brush, handspray, high and low pressure washing machines etc.
Rxsol PCS (Coal / Lime Remover) is an innovative, concentrated liquid product specifically engineered to attack, penetrate and remove Coal Carbon, pet coke, lime deposition accumulations from cargo and storage tanks, AlsoDeveloped for cargo hold cleaning to remove stains and discoloring after discharge of cargoes such as pet coke, coal, lime and other oily type cargoes.. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective
It is special blend of synthetic detergents and holding agents to increase its effectiveness on vertical surface.Recommended to use spray equipment.
• Effectively removes, Coal Carbon, pet coke and mineral & lime deposits from cargo holds and tanks.
• Can also be efficiently used as a general purpose cleaner to eliminate bad odors in tanks and other closed systems.
• Acts quickly and thoroughly.
• Can safely be used on all metals and metal alloys (even if painted/varnished).
• Non–flammable, non–toxic, non–conductive & non–volatile.
• Soluble in seawater and fresh water.
• No known effect on rubber or plastic compounds.
• May be combined with a specific range of other products.
• Cost effective, easy to apply and use.
EMULSION BASED non reactive coating materials which makes thin film barrier on surface after dry. Due to formation of RXSOL THIN barrier film on surface, the cleaning operation after unloading becomes quicker and easier with optimum results. Part No.- RXSOL-22-2210-210
Slip Coat RXSOL HOLD BLOCK is a Heavy Duty protective Solution for hold of vessels which carrying corrosive and / or messy cargos such as Sulphur, Salt, Petcoke, coal and concentrates. It can be easily removed after discharging of cargo .
FEATURES AND BENEFITS:...................................
$ Protects metal against corrosive cargo.
$Safe on all coatings, and to the personnel handling it.
$ Protects paint against cargo penetration.
$ Environmentally friendly .
$ Safe to use in occupied / covered areas.
$ Reduces turn around times .
$ Easy to Direct Spray.
RXSOL HOLD BLOCK is a Heavy Duty protective Solution for hold of vessels , which carrying corrosive and / or messy cargos such as sulphur salt petcock coal and concentrates. It can be easily removed with it
Recommendation Dose for smooth surface :
for Sulphur, Salt, etc 100 Ltrs/Hold for HANDYMAX & 150 Ltrs/Hold for PANAMAX
& for Petcoke, Coal, etc 200 Ltrs/Hold for HANDYMAX & 250 Ltrs/Hold for PANAMAX
This materials can be use directly with low pressure machine or manually by garden spray pump. in general practice on smooth & clean surface each drums of 210 ltrs covers 2000 to 2500 sq meter while on rough and rusted surface require more quantities of materials.
Note ::: This coated products are very easy to remove after uses of cargo as and when required ... one of this product can be use further :::
RXSOL-20-3018-025 Mixture of Emulsifier, new technology surfactants suitable for Metals and all areas . Acts as superior quality cleaner/ degreaser .Specially modulated for cargo hold cleaning operations after discharge of oily cargoes carried as dry bulk. Also The product has been developed for cargo hold cleaning to remove stains and discoloring after discharge of cargoes such as pet coke, coal, and other oily cargoes.
RXSOL-20-3018-025 has numerous general cleaning applications including the removal of greases, oil, sludge, carbon deposits, general dirt and grime. Can be used as engine room cleaner Suitable for cargo tank cleaning. Can be used as accommodation cleaner for bulkheads, decks, toilets. Suitable for cleaning of soiled textiles as rugs, covers, mats, overalls, etc. Effectively cleans glass fiber boats, hulls and painted surfaces Read the Material Safety Data Sheet before using this product.